粗大浓稠硕大噗嗤噗嗤h,精品人妻码一区二区三区,国产av无码专区亚洲精品,日韩a片无码毛片免费看小说

天通設備水處理 污水處理廢水處理成功案例

水處理的方式包括物理處理和化學處理。人類進行水處理的方式已經有相當多年歷史，物理方法包括利用各種孔徑大小不同的濾材，利用吸附或阻隔方式，將水中的雜質排除在外，吸附方式中較重要者為以活性炭進行吸附，阻隔方法則是將水通過濾材，讓體積較大的雜質無法通過，進而獲得較為干凈的水。另外，物理方法也包括沉淀法，就是讓比重較小的雜質浮于水面撈出，或是比重較大的雜質沉淀于下，進而取得�；瘜W(xué)方法則是利用各種化學藥品將水中雜質轉化為對人體傷害較小的物質，或是將雜質集中，歷史最久的化學處理方法應該可以算是用明礬加入水中，水中雜質集合后，體積變大，便可用過濾法，將雜質去除。

 鋼鐵廠廢水處理回用工程方案

  一 鋼鐵廠廢水處理工程概況

該鋼廠形成600萬噸/年生產規模時，平均排水量將達到4000m?/h。廢水處理工程設計平均日處理能力9.6萬米3，夏季最大日處理能力10.8萬米3,其中70%作為工業補水回到廠區管網，其余達標后排放。

  該廢水處理回用工程于2010年4月開工建設，2012年1月主體結構完工，2012年5月試運行，2012年8月交付生產。工程占地29500㎡，新建建、構筑物占地8041㎡，綠化覆蓋率32%，靜態投資為8643萬元。

  廠區全部廢水經處理后達到排放標準，其中回用水經軟化、過濾、消毒等深度處理后，達到生產用水標準。

 二 處理工藝

  1 廢水設計水質

本工程原水屬典型的冶金工業廢水，處理后外排出水要求達到地方排放標準中的二級標準。本工程設計進水水質見下表：

                         設計廢水綜合水質

序號 水質指標  指標數值  備注

1 pH值 7.0~8.5 

2 SS/（mg/L） ＜200 

3 COD/（mg/L）  ＜150 

4 BOD/（mg/L）  ＜40

5 石油類/（mg/L）  10~20  通常為下限

6 總硬度/（mg/L）  300~480  以CaCO3計

7 暫時硬度/（mg/L） 250~350  以CaCO3計

8 鈣硬度/（mg/L）  120~220  以CaCO3計

9 總堿度/（mg/L）  250~350  以CaCO3計

10 含鹽量/（mg/L）  1100~1300

11 總鐵/（mg/L）  ＜0.1 

12 CI-/（mg/L）  ＜260  一般為120~140

13 SO2-4/（mg/L） 190~220 

14 F-/（mg/L） 3~5 

15 溫度/（mg/L）  ＜35

廢水處理要求表見下圖：

                         廢水排放及回用限值

序號 水質指標  指標數值  外排限值  備注

1 pH值 7.0~8.5  6~8.5 

2 SS/（mg/L） ＜5  ＜30

3 COD/（mg/L）  ＜30 ＜50

4 BOD/（mg/L）  ＜10 ＜25

5 石油類/（mg/L）  ＜2  ＜4 

6 總硬度/（mg/L）  200~300  以CaCO3計

7 暫時硬度/（mg/L） ＜100  以CaCO3計

8 鈣硬度/（mg/L）  ＜30 以CaCO3計

9 總堿度/（mg/L）  ＜100  以CaCO3計

10 含鹽量/（mg/L）  ＜1100  

11 總鐵/（mg/L）  ＜0.1   

12 CI-/（mg/L）  ＜130   

13 SO2-4/（mg/L） ＜200   

14 F-/（mg/L） 3

15 溫度/（mg/L）  ＜35  

2 處理工藝

  本工程進水為典型的鋼鐵工業廢水，有機污染物含量不高，可生化性差，不適宜采用生化方法降解。本項目主要采用物理化學法。作為工業補水，在回用水深度處理中增加去除暫時硬度、總堿度軟化、過濾、消毒等工藝。

3 工藝流程

本工程的主要處理工藝流程可分為：預處理、澄清和過濾三部分

 廠區排出的工業廢水用管道輸送至廢水處理廠進水口。經過預處理部分，用粗、細格柵將來水中較大顆粒的漂浮物去除；再由提升泵到配水構筑物，在此投加混凝劑和石灰以及硫酸，然后將廢水分配到高密度澄清池，除去水中的懸浮物和膠體物質，保證水的澄清度，同時外排水還有除氟工藝。總進水的70%經高密度澄清池處理后，再經V形濾池過濾并投加液氯消毒后，送往廠區作為工業水的補充水，總進水的30%經高密度澄清池處理至達標后排放。                    

 電氣設計

 根據廠區總體布置規劃。結合供電專業對供配電系統的總體要求，采用雙路電源供電。在全廠設10/0.4kV總變電所一座，另外在預處理設10/0.4kV分變電所一座。并在V形濾池、高密度澄清池、加藥間和泥處理四處設MCC。全廠動力及照明負荷采用380/220V系統配電，裝機容量1800kW。本工程屬于二級用電負荷。

 自動化設計

  本工程包括預處理、高密度澄清池、加藥間、V形濾池、回水泵房和泥處理6個部分�？刂葡到y(tǒng)由基礎自動化級和過程自動化級組成�；A(chǔ)自動化有QUANTUM系列PLC和檢測儀表組成。PLC之間通過FIPWAY網實現數據交換。FIPWAY網上掛有工業PC作為入機接口，完成對整個系統的監控。過程自動化級由高檔PENTIUM微機及打印機組成，完成對工藝過程的生產管理、數據設定、報表打印等功能，在中央控制室還設有大型模擬屏顯示全廠的水處理工藝流程。

四  運行情況

1         監測結果

2012年5月正式運行，系統運行穩定，各項指標均達到設計值。年運行檢測數據（月平均值）見下表：

               2014 月平均數據

月份 pH值 SS/（mg/L） 暫時硬度（mg/L） 含鹽量（mg/L）

1月 7.6  4.12 70.0 1056

2月 7.5  5.00 75.0 1048

3月 7.3  4.81 75.0 1047

4月 7.2  4.00 80.0 1000

5月 8.0  5.00 85.0 1020

6月 8.1  4.75 85.0 1000

7月 8.1  4.07 90.0 990

8月 7.6  4.78 90.0 1000

9月 7.8  4.8  74.0 900

10月 7.8  5.00 78.0 1050

11月 7.9  5.00 76.0 1040

12月 7.8  4.8  90.0 1020

2         主要技術經濟指標

該廠區廢水處理工程投資8643萬元，勞動定員50人，裝機容量1800kW，運行日耗點22000kW?h，藥費0.12元/m?，年運行費1800萬元。噸水處理費0.80元/m?。

五  工程評析

  該廢水處理工程的建設采用公開招標，由我公司中標，其主要工藝系統高密度澄清池、V形濾池、全自動加藥及控制系統均采用該公司的技術和設備。作為核心單元的高密度澄清池是由我公司研制的一種斜管沉淀及污泥循環方式的高速澄清池，具有處理工藝占地少、處理效率高、管理方便等特點。

  本工程憑借先進的工藝、高自動化控制，投產以來運行良好。采用本工藝處理冶金行業廢水經濟有效，出水水質穩定，出水懸浮物小于5mg/L，COD小于15mg/L，污水含水率30%。

濟寧天通是一家水處理設備生產和銷售集一體的公司，公司擁有高尖端的技術人才，擁有高素質的工作團隊，可以及時地為客戶提供完善的售后服務。我公司主要產品：水處理設備，污水處理設備、廢水處理設備、工業污水設備、農業廢水設備、雨水凈水設備、醫院污水設備、鋼廠廢水設備、屠宰場廢水設備、食品廠廢水處理設備等多種設備，可根據要求專業定制水處理設備。

The way water is treated includes physical processing and chemical treatment. The ways in which human water treatment have been years of history, physical methods including the use of a variety of different aperture size, the filter material using adsorption or blocking way, exclude the impurities in the water, the adsorption mode of less important for adsorption on activated carbon, blocking method is through the water, the filter material for large impurity cannot pass, and get more clean water. In addition, the physical method also includes precipitation method, which is to make the impurity of the smaller proportion floating in the water, or the impurities of the larger proportion are deposited in the lower, and thus obtained. Chemical method is to use various chemicals to the water impurities into smaller material harm to the human body, or the impurity concentration, the oldest of the chemical treatment method should be use alum in the water, the water impurities after collection, volume change, used to filter method, remove the impurities.

Plant waste water treatment recycling project plan

An overview of wastewater treatment works in a steel plant

The average displacement of the steel plant will reach 4000m to the third/h when the steel plant is produced at 6 million tons/year. The average daily processing capacity of wastewater treatment works is 96,000 m 3, and the maximum daily processing capacity of the summer is 10.8000m 3. 70% of it is returned to the factory pipe network as industrial rehydration, and the remaining discharge after reaching the standard.

The waste water treatment recycling project started construction in April 2010. The main structure was completed in January 2012 and the trial operation was conducted in May 2012, and the production was delivered in August 2012. The project covers an area of 29500 ㎡, the new building and structures which covers an area of 8041 ㎡, green coverage of 32%, the static investment is 86.43 million yuan.

All waste water in the factory will meet the emission standard after treatment, and the water will reach the standard of production water after softening, filtering and disinfecting.

Two-process process

Wastewater design water quality

The original water of this project is a typical metallurgical industrial effluent, which is required to meet the secondary standard of local emission standard after treatment. The water quality of the engineering design is shown in the following table:

Design wastewater comprehensive water quality

Numerical value of the indicator of water quality indicators

1 pH 7.0 ~ 8.5

2 SS/(mg/L) < 200

3 COD/(mg/L) < 150

4 BOD/(mg/L) < 40

Oil/(mg/L) 10~20 is usually the lower limit

Total hardness/(mg/L) 300~480 with CaCO3

7 temporary hardness/(mg/L) 250~350 with CaCO3

Calcium hardness/(mg/L) 120~220 with CaCO3

Total alkalinity/(mg/L) 250~350 with CaCO3

Salt content/(mg/L) 1100~1300

Total iron/(mg/L) < 0.1

12 CI-/ (mg/L) < 260 is generally 120~140

13 so2-4 / (mg/L) 190~220

14 f-/ (mg/L) 3~5

15 temperature/(mg/L) < 35

The waste water treatment requirements are shown below:

Discharge and reuse of waste water

The numerical value of the numerical value of the indicator of the water quality indicator is noted

1 pH value 7.0 to 8.5, 6-8.5

2 SS/(mg/L) < 5 < 30

3 COD/(mg/L) < 30 < 50

4 BOD/(mg/L) < 10 < 25

Oil/mg/L < 2 < 4

Total hardness/(mg/L) 200~300 with CaCO3

7 temporary hardness/(mg/L) < 100 for CaCO3

Calcium hardness/(mg/L) < 30 for CaCO3

Total alkalinity/(mg/L) < 100 with CaCO3

Salt content/(mg/L) < 1100

Total iron/(mg/L) < 0.1

12 CI-/ mg/L < 130

13 so2-4 / mg/L < 200

14. F-/ mg/L) 3

15 temperature/(mg/L) < 35

2 treatment process

This engineering water is typical of steel industry wastewater, organic pollutant content is not high, but biochemical difference is not suitable for biodegradation. This project mainly adopts physical chemistry method. As an industrial rehydration, the process of removing temporary hardness, softening of total alkalinity, filtration and disinfection is added in the treatment of water reuse.

3 process flow

The main processing process of this project can be divided into three parts: pretreatment, clarification and filtration

The industrial effluent discharged from the factory is piped into the water inlet of the waste water treatment plant. After the pretreatment part, the large particles in the water will be removed by means of coarse and fine grille. By lift pump to the water distribution structures, again in the dosing coagulant and lime and sulfuric acid, and then assigned to high-density clarifier and wastewater to remove the suspended solids in the water and colloidal substances, ensure the clarity of water, drainage and fluoride in process at the same time. 70% of the total water treated with high-density clarifier, then through v-type filtration process and after adding the liquid chlorine disinfection, sent to the factory as make-up water of industrial water, 30% of the total water discharged after high-density clarifier processing to amount to mark.

Electrical design

According to the layout plan of the factory. The power supply is used to supply power supply for power distribution system. Set 10/0.4kV total substation in the whole plant. In addition, set 10/0.4kV substation. MCC is located in v-shaped filter, high density clarifying pool, interdrug and mud treatment. The power and lighting load of the whole plant is equipped with 380/220v power distribution and installed capacity of 1800kW. This project belongs to secondary electricity load.

Automation design

This project includes six parts: pretreatment, high density clarifying pool, additive medicine room, v-shaped filter, backwater pump room and mud treatment. The control system consists of basic automation level and process automation level. Basic automation has QUANTUM series PLC and detection instrument composition. Data exchange is realized through FIPWAY network between PLC. The FIPWAY has an industrial PC on the Internet as an incoming interface to complete the monitoring of the entire system. Process automation level is composed of high-grade PENTIUM microcomputer and printer, complete the process of production management, data set, report printing, etc, the central control room large mimic panel also has showed that the water treatment process for the factory.

Four operation conditions

1 monitoring results

In May 2012, the system was operational and the system was stable. All indexes were designed. Annual operation test data (monthly mean) see table below:

Average data for the month of 2014

Monthly pH value SS/(mg/L) temporary hardness (mg/L) salt content (mg/L)

January 7.1270.0 1056

February 7.5 5.00 75.0 1048

March 7.3 4.81 75.0 1047

April 7.2, 80.0 1000

May 8.0 5.00 85.0 1020

June 8.1, 4.7585.0 1000

July 8.4.07 90.0 990

August 7.78, 90.0, 1000

September 7.8, 74.0 900

October 7.85.00 78.0 1050

Nov. 7.9 5.00 76.0 1040

December, 7.8, 90.0, 1020

Main technical and economic indicators

The waste water treatment project in this factory has an investment of 8643 million yuan, 50 workers, 1800kW installed capacity, 22000kW? h, 0.12yuan/m cubed, and annual transportation fee of RMB 18 million. Tons of water treatment cost 0.80 yuan/m cubed.

Five project analysis

Adopts the public tender for the construction of the wastewater treatment projects, by our company won the bid, the main technology system of high-density clarifier, v-shaped filter, automatic dosing and the control system adopts the technology and equipment of the company. As the core unit of high-density clarifier was developed by our company a way of inclined pipe and setting and sludge circulation clarifier, treatment process covers an area of less, with high efficiency, convenient management, etc.

With advanced technology and high automation, this project has been well run since its production. The water quality is stable, the effluent suspension is less than 5mg/L, COD is less than 15mg/L, and the water content is 30%.

Jining day pass is a set of water treatment equipment production and sales of the company, the company has sophisticated technology talented person, has a high quality work team, can provide customers with perfect after-sales service in a timely manner. My company main products: water treatment equipment, sewage treatment equipment, wastewater treatment, industrial wastewater, agricultural wastewater, rain water purification equipment, hospital sewage equipment, steel plant waste water equipment, slaughterhouse wastewater treatment equipment, food factory waste water treatment equipment and other equipment, can professional custom according to the water treatment equipment.