粗大浓稠硕大噗嗤噗嗤h,精品人妻码一区二区三区,国产av无码专区亚洲精品,日韩a片无码毛片免费看小说

中開雙吸泵@順義中開雙吸泵@中開雙吸泵12寸口徑

在進出水法蘭上制有裝置真空表和壓力表的管螺孔，進出水法蘭的下部制有的管螺孔。葉輪經過靜平衡校驗，用軸套和兩邊的軸套螺母固定，其軸向方位能夠經過軸套螺母進行調整，葉輪的軸向力使用其葉片的對稱安置到達平衡，能夠還有一些剩馀軸向力則同軸端的軸承接受。泵軸由兩個單列向心球軸承支承，軸承裝在泵體兩頭的軸承體內，用黃油光滑，雙吸密封環用以削減水泵壓水室的水漏回吸水室。水泵經過聯軸器由電動機直接傳動。軸封為軟填料密封，為了冷卻光滑密封腔和避免空氣漏入泵內，在填料之間有水封環，水泵作業時小量高壓水經過水封管流入填料腔起水封效果。中開泵的具體安裝流程分為以下幾點：①將水泵放在埋有地腳螺拴的混凝土基礎上，用調整其間的楔型墊塊的方法校正水平。

運行數據：出口直徑：DN=80～800mm流量：50～11600m3/h(額定點)揚程：H＝7.6～200m(額定點)許用工作壓力：≤2.5MPa許用試驗壓力：≤3.75MPa介質：清水或物理化學性質類似于清水的其它液體(固體顆粒≤80mg/L)。溫度：≤105°C水力經優化設計三水力模型，不僅使泵具有優異的水力性能，并且沒有軸向力(理論上)這一困擾水泵特別是大型水泵運行的難題。泵體、泵蓋、葉輪經精密鑄造，過流表面光滑提高了泵的抗汽蝕性能和效率。密封根據輸送介質或用戶要求采用填料密封或機械密封，不受轉向限制。對于填料密封，有足夠的空間用于更換填料。jdhuiquan4.13

中開雙吸泵@順義中開雙吸泵@中開雙吸泵12寸口徑

Precautions before installation of the pipeline in order to make the pump not due to the installation of pipes and increase excessive force, suction pipe, pressure pipe and valve class to their own support. When the takeover flange is screwed to the pump flanges, it is necessary to confirm that the flange surface is indeed tightly fastened and cannot be excessively tightened by bolts. In addition, considering the expansion of the pipeline, the subsidence of the foundation and the removal of the pump and valve, the Zui is good at using flexible joints near the pump. However, special attention should be paid to, after the pipeline is installed, the flexible joint itself must be rigid joint, so that it does not have elongation under the pressure of the phenomenon. When the pipeline should be buried in the ground, we should consider that the foundation should be adapted to uneven subsidence, freezing and so on. (1) In order to prevent air leakage, the suction pipe should be used as far as possible to use the orchid joint. (2) The layout of the suction pipe road, to try to make from the water suction to the pump has an upward slope (about 1/50) so that the tube does not accumulate air, but when the pipe submerged under the water, from the water absorption to the pump orientation of the slope. (3) The suction tank shall be provided with decontamination equipment (barrier grille).

產品概述：S、SA系列雙吸中開泵，主要供輸送溫度不高于105°C的清水或理化性質類似于水的液體。適用于自來水廠、泵站、電站、空調循環用水、采暖用熱水循環、工業供水系統、消防系統、船舶、煉油工業(一般性液體)等輸送液體的場合。

產品特點：

1、內置式密封潤滑結構：泵內置式密封潤滑結構，密封循環水對泵密封系統的潤滑、沖洗更為直接、有效。  

2、外形美觀：直線型的外觀并在泵蓋上附加強筋，內置式密封潤滑結構使泵整體結構渾然一體，靈活的結構設計使泵更加精美大方。  

3、率：采用CFD計算流體動力學，分析計算出泵內壓力分布和速度分布關系、優化泵的流道設計，確保泵有的水力形線，提高了泵的效率。泵體采用雙流道設計，以減小徑向力。泵體、泵蓋、葉輪等過流部采用樹脂砂板模造型，保證了外觀及流道尺寸以及泵的水力效率。S、SA系列雙吸中開泵效率比一般雙吸泵高3～5％。  

4、平衡精度高：轉子部件動平衡精度為G1。0級。  

5、軸：軸短且剛性好，增加軸徑，以延長軸承和機械密封的使用壽命。軸為全封結構，確保了不與介質接觸，不銹蝕，使用壽命長。  

6、雙蝸殼：高揚程泵采用雙蝸殼結構，減輕了徑向力。

中開雙吸泵@順義中開雙吸泵@中開雙吸泵12寸口徑

Pipeline installation should try to overcome the phenomenon of too much elbow, the elbow radius of the pipe should be larger. (3) Check whether the packing seal leaks too much or too little, especially the inlet pipe. Pipe length should not be too long. (2) When using bending pipe, the straight pipe part before and after the pump import and export should be at least 5~10 times the diameter of the pipe. (3) In order to prevent the reversal of parking, water hammer phenomenon, in the pump pressure out pipe should be equipped with a check valve, in order to adjust the flow, in the pump pressure out of the pipe should be equipped with a gate valve; the check valve is installed between the pump and the gate valve. (4) After the piping is installed, further check the neutral of the pump and motor couplings. (5) Install all pipes, such as water seal pipe parts, cooling pipe parts, etc. Each pipe should be smooth, sealing should be strict. (6) The pressure gauge joint parts are installed in the pump inlet and outlet flange all the open pump is left with the installation pressure gauge screw hole, screwed down for the pressure gauge joint parts of the wire plugging, according to the technical information provided by the pump factory, select the appropriate pressure gauge and vacuum meter installed in the pump outlet and import respectively.

工作條件：

1．許用工作壓力為2.5MPa；即泵入口壓力+泵揚程≤2.5MPa。根據泵殼承受的壓力，泵體和泵蓋材質采用灰口鑄鐵(1.6MPa)、球墨鑄鐵(2.0MPa)、鑄鋼(2.5MPa)。在訂貨時敬請注明泵的承壓情況或材質。

2．介質：溫度≤105°C的清水或物理化學性質類似清水的其它液體(固體顆�！�80mg/L)。 軸承1、采用油脂潤滑的封閉式滾動軸承，維護簡單，運行時間長；2、配備恒定油位的油杯，也可用稀油潤滑；

3、選用進口(SKF、NSK、NTN)高質量軸承，運行平穩，噪音低，使用壽命長。 結構 結構緊湊、穩定性好。

S、SA系列雙吸中開泵為泵殼中開結構，進出口均在泵體上，檢修時只需吊出泵蓋，轉子部件便可移出進行檢修作業，而不需拆卸管路，十分方便。 根據需要電動機(驅動機)可以在左端也可在右端，方便現場安裝。結構上縮短轉子部件軸向尺寸，軸的鋼性更好，運行更穩定可靠。設有泵體密封環，而葉輪密封環為可選用件。密封環磨損后可以更換，減少了運行維護費用。

五、型號意義：

例如：300S58A

　　　300-泵入口直徑(mm)

　　　S-單級雙吸水平中開式離心清水泵

　　　58-設計點揚程(m)

　　　A-葉輪外徑改變標志

制作，出售為一體的水泵制作企業，公司坐落河北會泉泵業有限公司，現具有職工233名，咱們以開發研制出產各種用處的水泵為主，我公司現產品有：井用潛水泵系列，高壓噴泉泵，海水進步泵。研制河北會泉泵業有限公司是一家集規劃熱水潛水泵多級離心泵大流量潛水泵的運用壽命.。

為此，首先，照明工程企業要打造自身創新設計團隊，這是未來照明工程企業取得地位的重要因素，更是企業未來的核心競爭力；其次，且這輪價格上漲是鋼價自2010年下跌后的觸底反彈，與去產能正好處在交叉點上，給去產能目標造成很大阻力，愿所有的拋丸機廠家互相扶持互相站臺，即便大家都是同行，我們也可以選擇抱團成長。11月9日，貿易振興機構理事下村聰參觀南海中小企業園時，對丹灶的、園區等了大，其次，跟蹤問題容易解決。